Cascamite Accelerator is used with Cascamite weatherproof wood glue. This accelerator cures the mixed glue to a handling strength in approximately 10 minutes. Ideal for use when you have urgent jobs or small assembly joints that require further processing within a tight timeframe.

Application – For best results, use on clean, dry, bare wood. With a brush or sponge, apply a thin film of hardener to one surface and the mixed cascamite to the other. Let the hardener sink into the wood until it’s touch dry.

The post Cascamite Accerator appeared first on Time & Weather Instruments.

This product may have changed its name over the years,  now UREKA, and it’s back to the original Cascamite powdered urea/formaldehyde resin glue for cabinet and dinghy building. It is a fully gap-filling, water-resistant (when tested against DIN Spec. 68602/3 Section B3), mould-resistant and non-staining, and is approved by Lloyds Register of shipping (Certificate No.. YSC/QA 115) under the Society`s Quality Approval Scheme.

This adhesive produces a bond stronger than the timber.

Mixing

By Weight

Use 2 parts of Cascamite powder to 1 part of cold water.

By Volume

Use 3.1/2 parts of Cascamite powder to 1 part of cold water.

Supplied in plastic sealed tubs.

Supplied with instructions.

Available Sizes: 125g, 250g, 500g, 1.5kg,  and 3kg, Tubs

The post Cascamite 125g, 250g, 500g 1.5kg and 5kg Tubs appeared first on Time & Weather Instruments.

GATOR GLUE sticks to most common substrates, will set hard in about 30 minutes and even sticks to wet surfaces!

GATOR GLUE is supplied as a liquid which is 100% seawater proof, gives exceptionally high bond strength and is resistant to most chemicals.

GATOR GLUE may be used internally or externally. Put simply, it is the essential glue for trade, household or hobby use.

GATOR GLUE can be used to bond most types of wood (hard, soft, exotic, painted), Formica, polystyrene foam, PU foam and glass wool to porous surfaces. Also adheres to metal, stone, ceramics, porcelain, glass, concrete, brick, masonry and various plastics. Typical areas of use include wood jointing and construction, window and door frames, door manufacture, stone repair, boat building, staircases, ladders, general household repair, hobby use and much, much more.

Available in 60ml, 150ml, 250ml and 500ml size bottles.

The post Gator Glue the Adhesive with Bite : Sizes 60ml, 150ml, 250ml, 500ml, appeared first on Time & Weather Instruments.

As well as bonding all common wood types (hard, soft, exotic, painted) LUMBERJACK PU WOOD ADHESIVES will also bond Formica, polystyrene, PU foam metal and glass wool and various plastics (including PVC) to porous surfaces. These products also adhere to stone, concrete, brick and masonry.

Benefits

· Fast setting – 45 minute set (Typical PVA based wood glue – 8-12 hours)

· Exceptional bond strength to wood and most common building surfaces.

· Internal and external use – excellent weathering and aging properties.

· Fully water proof to EN204 D4, including seawater.

· Products foam slightly on application to fill small gaps and increase overall bond strength.

· Excellent Chemical Resistance.

Areas For Use

· General wood jointing and construction

· Window and door frame manufacture

· Door manufacture

· Furniture manufacture

· Boat building

· Construction of staircases and ladders

· As a high quality insulation adhesive for foam/glasswool/fibre boarding

Limitations

· At least one of the surfaces to be bonded must be porous.

· Not suitable for polyethylene, polypropylene, Teflon or Nylon.

· Surfaces may be damp, but moisture content of wood must not exceed 30%w/w.

· As product expands slightly on curing, do not use on sheet laminate. Use STICK 2 CONTACT ADHESIVE.

· Only apply between + 5 and + 30oC.

· Ensure surfaces are always clamped during use.

· Setting times will be increased at low temperatures and low humidity.

Surface Preparation

The surfaces to be glued should be clean and free from dust, grease and other contaminants. At least one of the materials must be porous. Roughen non-porous surfaces to give a key for the adhesive. To assist cure and achieve maximum bond strength, slightly moisten one surface with a damp cloth. Do not over wet.

Application

Cartridge Products: Cut tip of cartridge taking care not to damage the thread. Fix nozzle, cut to required aperture and apply using standard sealant gun.

Liquid version: Remove cap, cut spout and apply. Replace cap after use.

Wearing of gloves is recommended. Apply adhesive evenly to one surface. If necessary, cover large areas with a fine toothed spreader. Assemble parts IMMEDIATELY and clamp for duration of cure (5-30 minutes at 20oc; longer at lower temperatures). After this time, the joint may be easily handled. Full and final bond strength will be achieved after 30 minutes for 5 minute set or 24 hours for 30 minute set.

NOTE: These products foam slightly on application to fill small gaps. Any excess foam/adhesive must be removed with acetone before the product sets or with a sharp chisel once set.

The post Polyurathane Glue 45 minute appeared first on Time & Weather Instruments.

Features at a glance
-750g

– waterproofs (including sea water)
– overpaintable when dry
– interior & exterior use
– dry in just 5 minutes
– best for resistance to most chemicals and acids
– colour – brown
– D4 strength
– conforms to EN 204

Suitable for:
– wood
– metals
– brick
– stone
– concrete

Limitations

One of the surfaces must be porous.

Not suitable for polyethylene, polyproperlene, teflon or nylon.

Moisture content of wood should not exceed 30%

As product expands slightly on curing, do not use on sheet laminate.

Only apply between 5C and 30C

The post Polyurethane Glue 5 minute appeared first on Time & Weather Instruments.

This product is supplied with a FREE woodworking supplies catalogue with over 100 pages packed with products for woodworkers. (This will only be sent with UK orders)
This product may have changed its name over the years but its still the same powdered urea/formaldehyde resin glue, for cabinet and dinghy building. It is afully gap-filling, water resistant (when tested against DIN Spec. 68602/3 Section B3), mould resistant and non-staining, and is approved by Lloyds Register of shipping (Certificate No. YSC/QA 115) under the Society`s Quality Approval Scheme.

This adhesive produces a bond stronger than the timber.

Mixing

By Weight

Use 2 parts of Cascamite powder to 1 part of cold water.

By Volume

Use 3.1/2 parts of Cascamite powder to 1 part of cold water.

Supplied in a sealed bag. We suggest that once opened you place in an air tight container away fron damp.

Supplied with instructions.

Available Sizes 200g 500g, 1kg, 1.5kg, 2kg, 3kg, 5kg.

The post Cascamite also known as Extramite and Polymite. 200g to 5kg appeared first on Time & Weather Instruments.

Features at a glance
-750g

– waterproofs (including sea water)
– overpaintable when dry
– interior & exterior use
– dry in just 30 minutes
– best for resistance to most chemicals and acids
– colour – brown
– D4 strength
– conforms to EN 204

Suitable for:
– wood
– metals
– brick
– stone
– concrete

Limitations

One of the surfaces must be porous.

Not suitable for polyethylene, polyproperlene, teflon or nylon.

Moisture content of wood should not exceed 30%

As product expands slightly on curing, do not use on sheet laminate.

Only apply between 5C and 30C

The post Polyurethane Glue 30 minute appeared first on Time & Weather Instruments.